iPhone 3G Repair Manual.pdf

(5230 KB) Pobierz

Installing iPhone 3G Vibrate/Ring Switch

Installing iPhone 3G Vibrate/Ring Switch

Tools used in this guide

Phillips #00 Screwdriver

Small suction cup

Spudger

Parts relevant to this guide

iPhone 3G and 3GS Mute Button

© 2010 iFixit — CC BY-NC-SA

www.iFixit.com

Page 1 of 10

1276941671.051.png

1276941671.062.png

1276941671.073.png

1276941671.080.png

1276941671.001.png

1276941671.002.png

1276941671.003.png

1276941671.004.png

1276941671.005.png

1276941671.006.png

Installing iPhone 3G Vibrate/Ring Switch

Step 1 - Battery

Remove the two Phillips #00 screws from the dock-

connector end of the iPhone.

Step 2

Remove the metal handle from the suction cup. It's

easier and safer to grip the suction cup's base instead

of the metal handle.

Be very careful when opening the iPhone so

that the cables under the display are not

severed.

There is a rubber gasket between the silver

front bezel and black display assembly. A bit

of force is required in this step to separate

the iPhone's display assembly.

Use a small suction cup near the Home button to gently

pull up the bottom portion of the iPhone's display

assembly.

If the display assembly is too damaged to

allow the suction cup to adhere, tape with a

strong adhesive such as duct tape maybe

used.

Step 3

The display assembly is still connected to

the iPhone by several cables, so don't try to

remove it entirely just yet.

Rotate the display assembly up until it is at an angle of

approximately 45 degrees.

© 2010 iFixit — CC BY-NC-SA

www.iFixit.com

Page 2 of 10

1276941671.007.png

1276941671.008.png

1276941671.009.png

1276941671.010.png

1276941671.011.png

1276941671.012.png

1276941671.013.png

1276941671.014.png

1276941671.015.png

1276941671.016.png

1276941671.017.png

1276941671.018.png

1276941671.019.png

1276941671.020.png

1276941671.021.png

1276941671.022.png

1276941671.023.png

1276941671.024.png

1276941671.025.png

1276941671.026.png

1276941671.027.png

1276941671.028.png

1276941671.029.png

Installing iPhone 3G Vibrate/Ring Switch

Step 4

Continue to hold the display assembly with one hand,

and use your other hand and a spudger to disconnect

the black ribbon cable labeled "1."

Step 5

Rotate the display assembly up until it is roughly

vertical. This will allow easier access for disconnecting

the remaining cables.

Use a spudger to disconnect the black ribbon cable

labeled "2."

Step 6

Some iPhone 3Gs may have the connector

colors reversed (black plastic tab, white

connector). Make sure you're flipping up the

tab properly, otherwise you may damage

the connector.

Use a spudger to flip up the white plastic tab holding

the remaining ribbon cable in place. The white tab will

rotate up 90 degrees, releasing the ribbon cable.

Slide the black ribbon cable out of its connector, and

remove the display assembly from the iPhone.

Note: You may find on some versions of the

3G that the flip up plastic tab does not exist.

In this case you would slide the ribbon cable

towards the screen until it is removed. Upon

assembly, you would apply pressure to the

ribbon to insert it back into the ribbon

"socket".

© 2010 iFixit — CC BY-NC-SA

www.iFixit.com

Page 3 of 10

1276941671.030.png

1276941671.031.png

1276941671.032.png

1276941671.033.png

1276941671.034.png

1276941671.035.png

1276941671.036.png

1276941671.037.png

1276941671.038.png

1276941671.039.png

1276941671.040.png

1276941671.041.png

1276941671.042.png

1276941671.043.png

1276941671.044.png

1276941671.045.png

1276941671.046.png

1276941671.047.png

1276941671.048.png

Installing iPhone 3G Vibrate/Ring Switch

Step 7

Insert your SIM eject tool or a paper clip into the hole

next to the headphone jack.

Press down on the tool until the SIM card tray pops out.

Grasp the SIM card tray and slide it out of the iPhone.

Step 8

Use a spudger to disconnect the ribbon cable labeled

"4."

Step 9

Use a spudger to disconnect the ribbon cable labeled

"5."

© 2010 iFixit — CC BY-NC-SA

www.iFixit.com

Page 4 of 10

1276941671.049.png

1276941671.050.png

1276941671.052.png

1276941671.053.png

1276941671.054.png

1276941671.055.png

1276941671.056.png

1276941671.057.png

1276941671.058.png

1276941671.059.png

1276941671.060.png

1276941671.061.png

1276941671.063.png

1276941671.064.png

1276941671.065.png

Installing iPhone 3G Vibrate/Ring Switch

Step 10

Use a spudger to disconnect the ribbon cable labeled

"6."

If you have an iPhone 3GS, refer to picture 2 and use a

spudger to disconnect the ribbon cable labeled "7."

Step 11

Carefully peel up the small sticker labeled "Do not

remove."

© 2010 iFixit — CC BY-NC-SA

www.iFixit.com

Page 5 of 10

1276941671.066.png

1276941671.067.png

1276941671.068.png

1276941671.069.png

1276941671.070.png

1276941671.071.png

1276941671.072.png

1276941671.074.png

1276941671.075.png

1276941671.076.png

1276941671.077.png

1276941671.078.png

1276941671.079.png

Plik z chomika:

Inne pliki z tego folderu:

iPhone 3G Repair Manual.pdf (5230 KB)
iPod Touch 1st Generation Repair Manua.pdf (4058 KB)
iPod Touch 2nd Generation Repair Manual.pdf (5456 KB)
iPod Shuffle 1st Generation Repair Manual.pdf (3226 KB)
iPod Nano 2nd Generation Repair Manual.pdf (4770 KB)

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin